HOSTNAME: not connected
IP ADDRESS: not connected
FW VER: not connected
SOURCE:
IN TX0:
SOURCE:
IN TX1:
VIDEO TX0:
VIDEO TX1:
AUDIO TX0:
AUDIO TX1:
AUDIO OUT:
EDID TX0:
EDID TX1:
PORT SELECTOR:
TX0:
TX1:
INPUT 0:
INPUT 1:
INPUT 2:
INPUT 3:
VIDEO FLAGS:
AUDIO FLAGS:
HDR FLAGS:
HDR/HDR10+ and HLG not need to be checked if display already support
DV FLAGS:
Create DV string under DV tab
MATRIXMODE:
Copy sink EDIDs directly without applying EDID flags
WARNING:
AUTOMIXED EDID HAS OVERFLOWED
Audio Vendor Specific Descriptor Removed
HDR10+ Descriptor Removed
Audio replaced with LPCM Stereo + Atmos caps
DV descriptor removed
DOWNLOAD ACTIVE EDID TABLES:
SAVE ACTIVE EDID TO CUSTOM EDID 10:
UPLOAD EDID TABLES:
TX1 4K60 SDR:
TX1 4K60 HDR:
TX1 4K30:
TX0 No Upscaling
CAPTURED INPUT HDR METADATA:
EOTF:
GRN:
BLU:
RED:
WP:
Max/Min Lum:
MaxCLL/FALL:
HDR METADATA GENERATOR:
Max Luminance [nits]:
Min Luminance [nits]:
MaxCLL [nits]:
MaxFALL [nits]:
CAPTURED AVI METADATA:
VIC:
Colorimetry:
Range:
CUSTOM AVI METADATA GENERATOR:
AUTO LOW LATENCY MODE CONTROL:
Allows to control the TV supported ALLM feature
ON -setting forces ALLM enabled at all times - ignores RX ALLM
OFF -setting forces ALLM disabled at all times - ignores RX ALLM
FOLLOW -setting lets the source control enable/disable
ALLM MODE:
Assign to input:
UHD ALLIANCE FILM MAKER MODE:
OTHER CAPTURED METADATA:
SPD INFOFRAME:
AUD INFOFRAME:
HVS INFOFRAME:
VSI INFOFRAME:
HFV INFOFRAME:
CAPTURED INPUT DOLBY VISION METADATA [from source]:
DV Status:
DV interface:
Backlight metadata:
Backlight Max Luminance:
Auxiliary runmode:
Auxiliary version:
Auxiliary debug:
CONNECTED DOLBY VISION EDID DATABLOCK [sink tx0]:
DV Version:
DV DM Version:
DV Interface:
2160p60:
YUV422 12bit:
Global Dimming:
Backlight Control:
RED Primary:
GREEN Primary:
BLUE Primary:
MAX/MIN Luminance:
CONSTRUCT CUSTOM DOLBY VISION DATA BLOCK (for advanced users only):
Generates a 12-byte DV Version 2 Data Block. Select AUTOMIX with CUSTOM STRING -flag to activate.
RED Primary X:
RED primary Y:
GREEN primary X:
GREEN primary Y:
BLUE primary X:
BLUE primary Y:
MAX luminance [nits]:
Range 100 - 10000 nits
MIN luminance [nits]:
Range 0 - 1 nits
OSD SETUP: [press SEND after config]
FADE SECONDS: [OSD video]
FADE SECONDS: [OSD no input]
OSD TEXT SETUP:
CEC / EARC / ARC SUPPORT:
CEC must always be enabled to support CEC channel switching
VERTEX2 supports ARC and EARC audio return from the connected display
ARC/EARC support requires "0x05 Audio Processor", make sure no other AVR devices are connected to the TV
All changes to CEC/ARC parameters on this page require a VERTEX2 power cycle. Unplug/replug power.
CEC TYPE:
ARC mode default switching for AUDIO OUT between TV ARC and input HDMI
Some TV's won't release ARC line when watching input HDMI, these settings can override:
EARC mode default switching for AUDIO OUT between TV EARC and input HDMI
Normally EARC is always active once established, these settings can override:
Construct custom EARC CDS (for advanced users only):
TV/CEC TEST AND CONTROL:
Issue CEC command to turn the TX0 connected TV on/off:
Automate using "set ceccmd poweron" and "set ceccmd poweroff" ip commands:
TV CONTROL:
Issue any CEC command to the entire CEC network:
Automate using "set ceccmd xx" where xx is the command in the form aa:bb:cc:dd..
Ex. set ceccmd e0:36
SEND CEC TEST COMMANDS:
RS232 COMMANDS:
RS232 BAUD RATE:
VERTEX2 SETUP:
AUTOSWITCH INPUTS: Reboot required after changes. ON SENSE -only for advanced users.
HDCP VERSION:
HTPC MODE RX0:
HTPC MODE RX1:
HTPC MODE RX2:
HTPC MODE RX3:
OLED DISPLAY:
ROTATE 180 DEG:
REVERSE COLORS:
OLED FADE:
OLED PAGE:
REBOOT TIMER(hours):
AUDIO OUT FORMAT:
MUTE TX0 AUDIO:
MUTE TX1 AUDIO:
IR:
IR CODE SET:
TX0 +5V FORCE:
TX1 +5V FORCE:
SONY ANDROID TV FIX:
ANALOG L/R AUDIO CONTROL:
TEST PATTERN GENERATOR:
PATTERN:
HDCP:
IP CONFIG:
Reboot required for any changes in DHCP / STATIC IP
DHCP:
mDNS:
Current IP Configuration:
IP ADDR:
IP MASK:
IP GW:
MAC:
Configure Static IP:
This address is used when DHCP is off
IP ADDR:
IP MASK:
IP GW:
IP MASK:
IP GW:
Configure TCP port: [requires reboot to apply]
VERTEX2 will listen to this port for IP / Telnet commands
IP INTERRUPTS:
IP PORT:
VERTEX2 CONTROL:
REBOOT UNIT
EXPORT CONFIG
ISSUE HOTPLUG
RESET TO FACTORY DEFAULTS: